8 Simple Strategies To Constructing Inexpensive Bunk Beds For Youngsters

By Douglas R. Williams

To build bunkbeds for your own youngsters, you must have the supplies and equipment ready, start creating the mattress frame, attach the 38-inch beam to the 75 inches beam, drill 2 holes into the ends of the 75 inches beams, connect the plyboard sheet, drill holes into the 88 inch posts, start assembling the bunkbed, and connect the mattress and dowels.

Several moms and dads would like to have their youngsters sleep on bunkbeds to save on space. Here are the ways you could follow to create cheap kids bunk beds:

Have the supplies and also equipment ready

You’ll need 4 posts that measure 8x8x12 inches tall, four beams that measure 2x4x38 inches, 4 beams that measure 2x4x75 inches, plywood sheets that measure x38x75 inches, 2 dowels having 175 in. measurements, sixteen three-inch wood screws, sixteen ten-inch bolts with washers as well as nuts, 25 1-inch wood screws, sand paper, a drill with auger, screwdriver as well as regular bits, a circular saw and a longer, thin nail.

Begin building the mattress structure

Get two pieces from every single beam type which you have, 8 of the three-inch wood screws, 12 of the one-inch wood screws, a plyboard sheet as well as the nail and drill. The particular drill bit you use should really be smaller compared to the three-inch wood screws diameter. Begin drilling into the 2 edges of one the seventy-five-inch beams and make sure to drill through the face. There needs to be a length of about one inch between the slots as well as the end of the beam.

YouTube Preview Image

Attach the 38-inch beam to the 75-inch beam

Set the 38-inch to the 75-inch beams so that they make an L shape. Square them off in order for their surfaces may fall into line. Drive a nail into the screw slots you created in the 75-inch beam until it marks the 38-inch beam. Drill 2 additional holes into the 38-inch beams tip. Repeat the drilling operation for the contrary tip of the seventy-five-inch beam. Drive the wood screws to the slots you drilled to connect the 38-inch beam to the seventy-five-inch beam. Repeat the drilling procedure for the second seventy five-inch beam.

Drill 2 holes to the ends of the seventy five-inch beams

Make use of a drill bit that is a bit bigger than the bolts diameter and start drilling two slots at the end of the 75-inch beams. The actual holes should be half an inch from the internal side of the 38-inch beam so when lined horizontally it should be half an inch from one another as well as from the border.

Attach the plywood sheet

Put the plywood sheet on the frame you have formed. Now you can affix it to the frame with the 1-inch wood screws. Utilize 1 screw for every corner, 2 for the longer parts and 1 for the shorter sides.

Drill holes to the 88 inch posts

Start creating the support frames by drilling slots into every one of the 88 inch posts. Utilize a drill bit that’s a little bit larger than the bolts diameter. The slots should’ve a distance of 2 inches from the edge of the wood and one ft . from the end of the post. Drill an additional hole which is perpendicular to the other drill slots. It should have a size of one inch and should be six inches apart from the end of the post. The particular auger bit must be utilized for this phase. Continue doing this stage for the other three posts.

Start creating the bunk bed

Set the framework of the bed with the lower pair of holes on the posts. Affix the framework as well as the posts together utilising 8 bolts and washers. Continue doing this phase for the frame of the upper bunk.

Connect the dowels and mattress

Typically the dowels will be used as safety side rails for the bed, so slide these into the largest slots. Once the dowels are fastened tightly, now you can add the bed mattress.

You have now successfully built a bunk bed for your kids.

About the Author: Written by Douglas R. Williams. If you’d like ready-made

cheap kids bunk beds

, be sure to visit http://www.bunkbedsnow.com/cheap-kids-bunk-beds.html.



Permanent Link: